Transform Your Intercom Unit in Minutes
Your motorcycle communication system is essential gear - why not make it look as good as it performs? OzDecalz Intercom skin wraps let you customize your Packtalk, Egde, Pro or Custom unit with premium vinyl designs that protect and personalize.
(Soon to come are other units)
This guide will walk you through the complete installation process for bubble-free, professional results every time.
What's Included in Your Intercom Skin Wrap Kit
- Pre-cut vinyl skin pieces designed specifically for your intercom model
- Precision-cut openings for buttons, ports, and mounting clips
- High-quality Australian-made vinyl with air-release technology
What You'll Need
- Your OzDecalz Intercom skin wrap
- Microfiber cloth
- Squeegee or credit card wrapped in soft cloth
- Hairdryer or heat gun (optional, for curved edges)
- Good lighting and a clean workspace
Before You Start: Prep Your Intercom Unit
Step 1: Remove from helmet
Detach your intercom unit from the helmet mount for easier handling and complete coverage.
Step 2: Clean thoroughly
Use a microfiber cloth to remove all dirt, oils, fingerprints, and residue. Pay special attention to edges and corners. Let dry completely (2-3 minutes).
Step 3: Identify each piece
Lay out all skin pieces and identify which goes where. Most kits include: main body piece, side panels, and button area pieces.
Installation: Step-by-Step
Main Body Panel
1. Position without peeling
Hold the main piece against your intercom unit to understand the alignment. Note where buttons, ports, and clips line up.
2. Peel and apply top edge first
Peel back about 1-2cm of the backing from the top edge. Align carefully with the top of your unit and press down firmly.
3. Work downward slowly
Gradually peel more backing while smoothing the vinyl down with your squeegee. Work from centre outward to push air bubbles toward the edges.
4. Wrap around edges
For curved edges, apply gentle heat with a hairdryer (low setting, 15-20cm away) to make the vinyl pliable. Wrap it around edges and press firmly.
Side Panels and Detail Pieces
5. Apply smaller pieces
Use the same technique for side panels and button area pieces. Align carefully before committing - these precision-cut pieces have less margin for error.
6. Seal all edges
Run your squeegee firmly along all edges and seams. This is critical for longevity - unsealed edges will lift over time.
Button and Port Cutouts
7. Check all openings
Verify that all button cutouts, charging ports, and mounting clip areas are properly aligned and not covered.
8. Trim if needed
If any vinyl slightly overlaps a button or port, carefully trim with a sharp blade. Less is more - you can always trim more, but you can't add back.
Final Steps
Press and seal
Go over the entire unit one more time with firm pressure, paying extra attention to edges and corners.
Pro Tips for Perfect Intercom Skins
- Temperature matters: Install in 18-25°C conditions. Cold vinyl doesn't stick well; hot vinyl is too stretchy.
- Don't stretch: Let the vinyl lay naturally. Stretching causes it to shrink back and lift later.
- Heat is your friend: For tricky curves and edges, low heat makes vinyl incredibly workable.
- Patience on corners: Corners and edges are where most people rush. Take your time here.
- Air bubbles: Small bubbles often disappear within 24-48 hours. For stubborn ones, gently lift the edge, reapply, and squeegee out.
Common Mistakes to Avoid
- Skipping the cleaning step - oils and dirt prevent adhesion
- Applying in direct sunlight or on a hot unit
- Rushing the edge-wrapping process
- Not sealing edges properly with heat and pressure
- Remounting to helmet immediately instead of letting it cure
Caring for Your Intercom Skin
Once installed, your intercom skin is durable and weather-resistant. To keep it looking fresh:
- Wipe clean with a damp microfiber cloth
- Remove and clean your intercom periodically to check skin condition
Browse Our Intercom Skin Collection
Ready to customize your comms unit? Check out our full range of intercom skin wraps - from bold graphics to sleek designs.
Or join our Rider Skinz Club and get fresh intercom skin designs delivered quarterly - always ride with a fresh look.
Designed and made in Australia. Built to last.
Questions about installation? Contact us - we're here to help you get it perfect.